The Powerstick-6 is a 4 x 6.5" / 1 x 1" column format loudspeaker.

The slim design makes it very unobtrusive for its high performance class and integrates discreetly into any environment. The beautifully curved grille and the slightly trapezoidal housing, without interruption of the side line by handles, emphasize the elegant appearance.

The passive linearization allows operation with any power amplifier without additional DSP filtering. The asymmetrically radiating tweeter horn and the coupling of the 6.5" chassis with each other, with the resulting vertical bundling of the sound energy, guarantees a high range over the entire frequency range. The Powerstick-6 achieves excellent intelligibility even in acoustically difficult rooms. A very powerful 1" driver is used in the high frequency range, which, with its low distortion and resonance, keeps up very well with the sound pressure of the four midrange drivers without becoming strained or obtrusive at higher volumes. The Powerstick-6 has powerful low-mids and sounds very natural and finely resolving and meets even the highest demands.

The performance of the Powerstick-6 is comparable to a very good 12" top, but with advantages in range and the visually appealing, slim design.

The dual-tilt high stand flange allows the speaker to be tilted with 0° and 5° positions.

For good handling in mobile use, there are two generously sized handles on the back. The optionally available carrying bag is the ideal accessory for easy transport and protects against signs of wear.

Various threaded points, U and C swivel brackets, and wall brackets are available for flight operation or mounting in installations. A safety point allows a single stud with safety rope to be clicked into place for the prescribed secondary safety.


  • Plug&Play passive to any suitable amplifier, even without DSP.
  • Plug&Play on the TENNAX self-powered Subwoofern (Combi-Sets).
  • Plug&Play on Powersoft amplifiers with ready-to-use presets for Armonia Plus software.
  • About the TENNAX (AllDSP) 19“ DSP-Controller with any suitable amplifier. Filter values are already set, limiter values can be adjusted by yourself (Limiter preset to 32 dB amp gain).

Technical Data

LF: 4 x 6,5" Bass-midrange driver
HF: 1 x 1" Compression driver

Frequency range
70 Hz - 22 kHz (- 10 dB)
140 Hz - 20 kHz (+/- 3 dB)

Coverage range (h x v)
asymmetric 100° to 50° x 55°

4 Ω

Powerhandling (AES / program / peak)
500 W / 1.000 W / 2.000 W

Sensitivity 1 W/1 m
96 dB SPL

Sound pressure at (AES / program / peak)
123 dB SPL / 126 dB SPL / 129 dB SPL

2 x Neutrik NL4 IN/OUT 1+/- (4-pole looped-through)

Polyurea coating in RAL 9005

Dimensions / Weight
985 (H) × 220 (W) × 338 mm (D) / 24,6 kg



Carrying bag for Powerstick-6


Carrying bag for 1 x Powerstick-6. Strong Codura fabric with padding.

U-bracket for Powerstick-6


Stable swivel bracket for installation on trusses and ceiling. 2 x M10 hexagon head screws included in delivery.

C-bracket for Powerstick-6


Stable swivel bracket for vertical or horizontal installation on trusses, walls and ceiling. 2 x M10 hexagon head screws included in delivery.

Flat knurled screw M10 x 25 mm


Flat knurled screw M10 x 25 mm, steel black burnished for all u- and c-brackets. As an alternative to the hexagonal bolts supplied with the brackets.

Hand lever M10 x 30 mm


Hand lever M10 x 30 mm, adjustable, flat design, steel black burnished with plastic lever, suitable for all U- and C-brackets.

Self-lock clamp


Loudspeakers can be flown by one person with the self-lock clamp. The clamp hooks directly into the truss and can be easily tightened. Load capacity 250 kg.

Truss clamp


With this traverse clamp you can easily and loosely mount your devices to all common traverses with 48-51 mm strap tubes. The clamp impresses with its compact design, its lightness and the maximum tensile load of 100 kg. Locking screw M8 Wing nut and device screw M10.

Eye Bolt M10 x 40 mm


M10 x 40 mm eyebolt, for M10 mounting points. Load capacity 250 kg.

Single stud


Single stud for securing a loudspeaker with safety cable.

Safety 6/1000


1 m safety cable 6 mm Ø for securing a suspended loudspeaker. One side with a screwable quick connect.

Wall holder flange big


Stable wall holder with tilt and swivel orientation: 180° horizontal, 22° vertical adjustable in 11 steps. Expanding mandrel for play-free seating in the tripod base of the speaker. Max. load capacity: 50 kg.

Wall- and Trussholder


Wall- and Trussholder with a joint and a tube clamp, circa 520 mm long. Max. load capacity: 50 kg.

Multifunctional rotating ceiling bracket


For hanging speakers from ceilings using steel cables or chains and various accessories. Horizontal alignment due to central pivot axis. Max. load: 60 kg. Available in white and black. Supplied without further mounting accessories.

Telescopic rod


Telescopic rod with expanding mandrel system for play-free seating in the tripod base. Height: 110 to 180 cm. Max. load capacity: 35 kg.

Distance rod with crank


Distance rod for cranking with expanding mandrel system which provides a tight and firm fit for the speaker. Height: 92 - 152 cm. Max. load capacity: 50 kg.

Speaker stand crank


Stable stand for cranking with double protection against falling. Height: 139 to 218 cm. Max. load capacity: 50 kg.

Speaker stand


Stable stand with expanding mandrel system which provides a tight and firm fit for the speaker. Double protection against falling. Height: 132 - 220 cm. Max. load capacity: 50 kg.

Carrying bag for 2 x speaker stand/ rod


Carrying bag for two speaker stands or distance rods, also with crank. Two inside compartments with zipper and sturdy handles. Material waterproof nylon.

Cable Clip for speaker stand/ rod


The cable clip made of robust, durable ABS plastic is specially designed for speaker stands and distance rods with 35 - 36 mm tube. It adheres firmly to the tube and holds the cables securely and neatly in the 24 x 16 mm guide accessible from the outside.

Iron base with weight plate


The set includes a flat 10 kg iron base Ø 45 and a 5 kg weight disc. It is suitable distance rods with an M20 screw thread. The weight disc can be mounted tool-free.

Carrying bag for round base Ø 45 cm


Padded bag made of robust, water-repellent nylon, with space for a round base Ø 45 cm with weight disc. The bag has two carrying straps with a soft velcro handle, a sturdy zipper and a transparent window for labels.

speakON cable 0.5/1/3/6/10/15/20/30 m


Speaker cables in various lengths with Neutrik plug NL4FX. 4 x 4 sq mm, each wire 224 x 0.15 copper, diameter 11 mm, weight 273 g / m. Assembled with some pressed ferrules for maximum contact area and minimal contact resistance.

speakON adapter


Adapter to connect two speaker cables.

Connection plate with waterproof PG thread cable gland


The angled Speakon connector panel can be exchanged e.g. for installation purposes outdoors against a connector plate with waterproof PG thread cable gland.

Connection plate with Phoenix-contact connector strip


The angled Speakon connector panel can be exchanged e.g. for installation purposes for a connection plate with Phoenix contact plug connector.

Phoenix Contact


Phoenix Contact 4 pol. as an alternative to the Neutrik NL4 Speakon IN/OUT.